How to Replace a Mazda Key

Mazda is known for its innovative and intuitive technology. Some of these systems improve the safety and performance of vehicles, while others make driving around East Stroudsburg Easton and Brodheadsville more enjoyable.

The key fob is a fantastic example of the latter. It lets you lock, unlock, and start your Mazda with a button push. Its battery must be replaced on a regular basis.

Lost Keys

Keys that are lost or stolen are an absolute hassle. Luckily, it is fairly simple to replace the Mazda key for older models that have regular metal keys, however modern cars require special programmable computer chips which can only be purchased from the locksmith or dealer.

You'll need to start by finding the VIN number for your vehicle. It is usually found on the driver's side dashboard on your insurance card, or in the vehicle's documentation. Make sure to write down the information you need to provide it to the locksmith or dealership.

You will require an additional key that is functional. Put the key into the slot and switch the ignition on. Take the key out after five seconds and switch the ignition off. Repeat the procedure with the second key. Once both keys have been inserted, the new one's computer chip will pair with your car.

If you lose your keys and don't have a backup plan, you will need to have the vehicle towed to a dealer. Then, you'll have to prove ownership and pay for a replacement key. You might need to wait a few days until the dealer can order and install a new key to your vehicle. If you can, have a locksmith make a replacement key instead of a dealer for a lower cost and less hassle.

Ignition Cylinder Replacement

The ignition cylinder is a component of your Mazda that allows you to start the car by using an ignition key. If your Mazda isn't turning over or you are unable to insert the key into the switch, you may need to replace the ignition cylinder.

Ignition cylinders fail more often than keys, which last longer. There is no set maintenance schedule for them, however you can help them last longer by keeping your keys clear and avoid excessive jiggling or shaking of the key.

To replace the ignition cylinder, first take off the trim pieces and covers that are in the way. Depending on the model it could mean taking off the cover for the steering wheel or removing the accessory and wiper switches. Use a socket wrench or screwdriver to press the release tab on the cylinder. This frees the cylinder from the switch and allows it to slide out of the housing.

When the cylinder is removed, replace it by connecting it to the wires, tightening two screws on top and then replacing the switch cover. Reconnect the battery, and verify whether the new cylinder is able to insert or remove keys. Do this 3 to 5 times, and then reconnect the battery and attempt to start the vehicle to make sure everything is functioning correctly.

Remote Control Replacement

When your Mazda key remote isn't working, you'll require an expert to get it back in operation. While this isn't as common as a problem with the ignition cylinder but it does happen and can still cause you to be stranded in certain instances. Locksmiths can repair the car key duplication shop remote and take care of all the programming associated with it.

The most basic information you'll need to give a locksmith in order for them to perform this service is the model and year of your Mazda vehicle. This will enable them to gather the appropriate equipment and know that they'll require any additional programming of keys for your particular model of Mazda.

If your key fob isn't turning on, it might have a dead battery. In this scenario the best thing to try is to reset your receiver. This is often able to restore the functionality. If this doesn't work you must replace the batteries. To do this, you'll have to take the key off and then use a screwdriver with a flat head wrapped in tape to break the case open on one side. Once you've done this, insert a new battery into the key fob. Close the case and verify that it's compatible. The RF unit in your Mazda will need to be programmed to recognize the new key.

Transponder Chip Replacement

You may have you own a mazda keyless remote smart key or key fob. If that's the case you're driving a car, it's likely to have a transponder. This tiny piece of technology, which is essentially an electronic micro-motherboard, transmits an indication to the immobilizer in the car when it is placed in the ignition.

Keys like these are incredibly helpful in terms security, since they prevent others from starting your car, by ensuring that the only person who is able to start your vehicle is you. This is why you have to be vigilant to make sure that your key does not become lost or stolen.

Fortunately, transponder chips are able to be replaced by an experienced locksmith. To do this, you'll have to take off the cover on your key fob. It is usually an extremely thin piece of plastic that can be removed using the screwdriver. The next step is to remove the chip, which should look like an elongated black square or a tube that is transparent. Once you've done that, simply place the chip on a piece tape and attach it near to the ignition lock.

A reputable locksmith should be able to complete this task in a matter of minutes, and they'll be able to help you get your car back on the road as quickly as possible. If you're experiencing issues with your Mazda key, contact a trusted mobile locksmith right away.